CGSFT - BOAT ARMER NEUTRAL GEL-KOTE, BA5676

  • MSDS: CGSFT
  • Manufacturer: FIBRE GLASS EVERCOAT CO INC
  • Product Name: BOAT ARMER NEUTRAL GEL-KOTE, BA5676
  • National Stock Number: 8010-00N084107
Product Identification

Product ID:BOAT ARMER NEUTRAL GEL-KOTE, BA5676
MSDS Date:07/19/1991
FSC:8010
NIIN:00N084107
MSDS Number: CGSFT

Responsible Party
FIBRE GLASS-EVERCOAT CO INC
6600 CORNELL RD
CINCINNATI, OH 45242
US

Emergency Phone: 800-424-9300 (CHEMTREC)

Info Phone: 800-729-7600

Preparer: JEFF ZYCH

Cage: 18731

Contractor
FIBRE GLASS-EVERCOAT CO INC
CINCINNATI, OH 45242 US

Telephone: 513-489-7600

Cage: 18731

Ingredients

5

CAS: 100-42-5

RTECS: WL3675000

Fraction By Weight: 39.60%

OSHA PEL 100 PPM

ACGIH TLV: S, 50 PPM/100 STEL

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS


POLYESTER RESIN

Fraction By Weight: 60%

OSHA PEL N/K

ACGIH TLV: N/K


0 (CALCULATED)

RTECS: 9999999VO

OSHA PEL N/K

ACGIH TLV: N/K

Hazards

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:YES OSHA:NO
Health Hazards Acute and Chronic:ACUTE: INHAL: VAPORS MAY CAUSE NOSE,
THROAT & RESP TRACT IRRITATION. HIGH CONC MAY CAUSE HEADACHE &
NAUSEA. RPTD HIGH CONC EXPOSURE MAY CAUSE LIVER & KIDNEY DMG. SKIN:
PRLNGD/FREQUENT SKIN CONT MAY CA USE DEFAT, DRYNESS W/IRRIT &
POSSIBLE DERM. EYE CONT MAY CAUSE TEARING & IRRIT. SKIN ABSORP:
DERMATITIS(EFTS OF OVEREXP)
Explanation of Carcinogenicity:STYRENE: IARC MONO, SUPP, VOL 60, PG
233, 1994: GROUP 2B.
Effects of Overexposure:HLTH HAZ: & IRRIT. INGEST: MAY CAUSE GI
DISTURBANCES, PAIN & DISCOMFORT. CHRONIC: THE IARC HAS CLASSIFIED
STYRENE AS POSS HUMAN CARCIN (CLASS 2-B). THE 2-B CLASSIFICATION IS
NOT BASED ON NEW EVID THAT STYRENE MIGHT BE A CARCIN BUT ON A
REVISED IARC CLASSIFICATION SYS & NEW EVID FOR STYRENE OXIDE.
Medical Cond Aggravated by Exposure:LIVER AND KIDNEY DISORDERS.

First Aid

First Aid:SKIN: WASH WITH SOAP & WATER. EYES: FLUSH W/WATER FOR @ LST
15 MINS & GET MED ATTN. INHAL: REMOVE VICTIM FROM EXPOSURE. IF
UNCON GIVE ARTF RESP/OXYG AS NEEDED. GET MED ATTN. INGEST: DO NOT
INDUCE VOMI T (ASPIRATION HAZARD). GET MED ATTN.

Fire Fighting

Flash Point Method:CC
Flash Point:98.0F,36.7C
Lower Limits:1.1%
Upper Limits:6.1%
Extinguishing Media:FOAM, ALCOHOL FOAM, CO*2, DRY CHEMICAL, WATER FOG.
Fire Fighting Procedures:USE NIOSH APPROVED SCBA & FULL PROTECTIVE
EQUIPMENT .
Unusual Fire/Explosion Hazard:POLYMERIZATION MAY TAKE PLACE AT ELEVATED
TEMPERATURE SUCH AS IN A FIRE. IF CONTAINED, VIOLENT RUPTURE MAY
RESULT.

Accidental Release

Spill Release Procedures:REMOVE ALL SOURCES OF IGNITION. ABSORB SPILL
WITH ABSORBENT MATERIAL SUCH AS VERMICULITE OR SAND.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling

Handling and Storage Precautions:AVOID STORAGE ABOVE 100F. STORE ONLY
IN ORIGINAL CONTAINERS.
Other Precautions:NONE SPECIFIED BY MANUFACTURER.

Exposure Controls

Respiratory Protection:NIOSH APPROVED CANISTER TYPE RESPIRATOR MUST BE
WORN TO PREVENT INHALATION OF VAPORS OR SPRAY MISTS WHEN TLV/PEL IS
EXCEEDED. WEAR NIOSH APPRVD DUST MASK WHEN SANDING CURED PRODUCT.
Ventilation:PROVIDE SUFFICIENT MECHANICAL (GENERAL AND/OR LOCAL
EXHAUST) VENTILATION TO MAINTAIN EXPOSURE BELOW TLV.
Protective Gloves:PLASTIC OR CHEMICAL RESISTANT GLOVES.
Eye Protection:ANSI APPRVD CHEM WORKERS GOGGLES .
Other Protective Equipment:ANSI APPRVD EYE WASH & DELUGE SHOWER . USE A
BARRIER CREAM SUCH AS GLOVE COAT WHEN USING PRODUCT.
Work Hygienic Practices:REMOVE AND WASH CONTAMD CLTHG. WASH HANDS
BEFORE EATING & DO NOT SMOKE WHILE USING.
Supplemental Safety and Health
NONE SPECIFIED BY MANUFACTURER.

Chemical Properties

Boiling Pt:B.P. Text:SEE ING 1
Vapor Pres:SEE ING 1
Vapor Density:HVR/AIR
Spec Gravity:1.02 (H*2O=1)
Evaporation Rate & Reference:SLOWER THAN ETHER
Solubility in Water:NIL
Appearance and Odor:PASTE, SHARP AROMATIC ODOR.

Stability

Stability Indicator/Materials to Avoid:YES
STRONG ACIDS AND OXIDIZING AGENTS.
Stability Condition to Avoid:DIRECT SUNLIGHT.
Hazardous Decomposition Products:HEATING TO DECOMPOSITION MAY CAUSE
IRRITATING ACRID FUMES.
Conditions to Avoid Polymerization:IF HAZARDOUS POLYMERIZATION OCCURS
WHILE CONTAINED IN A CLOSED CONTAINER, VIOLENT RUPTURE MAY RESULT.

Disposal

Waste Disposal Methods:SMALL QUANTITIES CAN BE REACHED WITH THE APPROP
HARDENER TO SOLIDIFY. DISPOSE OF I/A/W FEDERAL, STATE AND LOCAL
REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.